Emefiele , a member of the Presidential
Task Force on Agriculture, disclosed this while fielding questions from
journalists at the Odeda Farm Institute, Odeda during the Task Force’s
inspection of the facilities of the Institute and some farm centres in
the state. The Presidential Task Force, which also included the Minister
of Agriculture, Chief Audu Ogbeh and the Kebbi State governor, Abubakar
Atiku Bagudu, were earlier conducted by the state governor, Senator
Ibikunle Amosun, round Eriwe Fish Farm in Ijebu-Ode, Greenhouse
Technology Centre, Kotopo in Abeokuta and Owowo Farm Settlement in
Ewekoro local government area. Emefiele added: “When we find a state
that is serious and ready to work with us, we burst the commercial
agricultural credit scheme facility that we have because the President
has mandated that those who are serious, we must support. That is the
essence of this.” He added that the Bank of Agriculture (BoA) will be
properly restructured by the Federal government towards assisting
farmers to boost agricultural production in the country and ensure food
sufficiency. Emefiele said that if the restructuring was eventually
done, it would help the bank to perform its primary responsibilities
well. The CBN governor explained that the team was mandated by the
president to go round the entire federation on a fact-finding mission on
how to resuscitate some of the age-long agricultural potentials of the
country. He added that the President specifically tasked the team to
locate how to ensure increase in the production of cassava, maize and
resuscitate cocoa production in the southwest emphasising maize
production will support the poultry productivity in the South Western
part of the country. He said, “For us to go round the entire federation,
not just about rice, tomatoes, millet but also about even coming down
South. What can we do to resuscitate some of our age-long agricultural
potential.”
“The swing boom is used almost daily for one reason or another,” Vinton says. “The older I get, the more I realize how much easier it is on my body to have this extra help lifting when needed.”
Vinton uses the hoist for anything from removing duals to servicing the mower deck. The crane can even remove a combine engine since the hoist allows for a full 16 feet of lift height.
How It’s Made
Nearly all parts of the crane were locally sourced, utilizing used iron from the farm and an oil gas line section for the pipe.The gas line is only ½-inch thick and 2 feet in diameter. Both ends were capped, and the bottom end has several shafts running through it to anchor the crane. Vinton buried it 6 feet deep into rebar-reinforced concrete. The pipe stands at 18 feet and pivots a 30-foot-long H-beam. The horizontal beam measures 18×8 inches with ½-inch flanges. With a full 1-ton load at its end, the beam flexes 1.5 inches.
“The head of the crane was built around an electric pallet jack frame with a top bearing from a semitrailer axle shaft and hub,” Vinton explains. “The lower bearings were from a salvaged electric forklift.”
The crane covers nearly 80% of the 60×124-foot shop with sidewalls extending up 19 feet. To handle the lifting, the jib style crane has a 2-ton air hoist and a 1-ton electric hoist. Combined, the head components weigh in at a hefty 2 tons.
Shop Design
The shop, built in 2001, features more than just the crane. The shop has a pass-through, 30-foot bifold door that allows for access from the shop into the machinery shed without opening up the building to the outdoors. Not only does this mean the family saves on its heating bill, but also that they can stay inside in the winter since bigger heads can get through the door.The shop features a second deck level, which has Vinton’s mill, big dill press, air compressor, and plenty of room for parts storage. Their crane makes it possible to move heavy equipment upstairs that they might not otherwise be able to carry.
To secure the shop, Vinton leaves nothing to chance. He has an alarm system to alert the service provider to call the authorities if there are any attempted break-ins. There is also a security cage under the shop’s overhead deck that houses special tools. One wall of the cage is a steel cabinet that can be locked to secure special electric and air tools.
Vinton was thinking ahead when he broke ground for his shop in 2001. The innovative design was set up to allow for easy future expansion.
“Our shop design serves us quite well, but it continues to be a work in progress. We’d still like to add a lathe, press, and more as used equipment becomes available,” he says.